top of page

Step 5 of a Payment Application: What the Owner Does After the Architect Certifies

Writer: Cost Construction Accounting
Cost Construction Accounting
8 minutes ago
4 min read

By Tammy Hoang, QuickBooks ProAdvisor — Construction Bookkeeping Specialist | Construction Cost Accounting

(949) 889-3283  |  constructioncostaccounting.com

Direct answer: once the architect has certified a payment application, the owner's next step is to issue payment directly to the contractor named on the application form. The owner should pay the exact company or individual named, and should not redirect funds to anyone else unless the submitted document explicitly says so. This keeps a clear paper trail and helps avoid disputes and delays.

This guide covers what the owner pays after certification, why the payee has to match the application, a worked example of the amount paid and the retainage held, and what the contractor should record when payment arrives. It builds on CCA's guide to creating AIA invoices.

1. What the Owner Pays After Certification?

The G702 is the Application and Certificate for Payment, and the architect's certificate for payment fixes the amount the owner pays in each progress billing cycle. Procore's G702 guide says the application generally serves as an invoice, and that once the architect or another party certifies it, payment follows. Source: Procore, AIA G702. Autodesk adds that payments are issued minus any retainage. Source: Autodesk Construction Cloud, AIA billing.

On timing, a Lorman summary of AIA A201 Section 9.6.1 states that the owner pays within the time set out in the contract. Source: Lorman, AIA 201 payment provisions. The sources I could read do not give a universal deadline, so the contract controls when payment is due.

Owner step after certification

What it means

Pay the amount certified

The amount certified on the G702, which already reflects any changes the architect made

Pay the contractor named on the application

The exact company or individual named, not someone else, unless the document explicitly says otherwise

Hold retainage as the contract provides

Payments are issued minus retainage, which the owner or general contractor holds until the job is complete

Pay within the contract's timeframe

The contract sets the time for payment

2. Why the Payee Must Match the Application?

CCA's guide gives the reason in plain terms: paying the named payee gives a clear paper trail and helps sidestep disputes or delays later. The application form is the record of who billed and who is owed, so a payment to someone else breaks the match between the document and the money.

There is also a fraud reason to keep the payee tied to the document. Wipfli reports an FBI-noted scheme in which criminals register a lookalike domain and email the party that issued the bid with "new" ACH payment instructions that route money to their own account. The fraud often surfaces only when the real company starts collecting on payments it never received. Wipfli's recommended defense is to verify any payment change out-of-band, call the vendor using a phone number known to be genuine, and require two different employee sign-offs for any change. Source: Wipfli.

Payee check

Purpose

Compare the payee on the check or transfer with the name on the application

Confirms the money goes to the contractor who billed

Treat any request for a different payee as a change to verify

Unless the submitted document explicitly names another payee

Verify changes by calling a known phone number, not the number in the email

Per Wipfli's recommended verification

Keep the application and the payment record together

Preserves the paper trail

Want every certified payment matched to your bank deposits?

Construction Cost Accounting helps contractors reconcile payments to certified applications with accurate construction cost accounting.

constructioncostaccounting.com  |  (949) 889-3283 

3. A Worked Example: What Is Paid and What Is Held?

Assume a $500,000 contract. The certified application shows $200,000 completed and stored to date, 10% retainage, and $120,000 certified on earlier applications. The retainage rate comes from the contract. The figures are illustrative arithmetic, not CCA client data.

G702 item

Amount

Total completed and stored to date

$200,000

Retainage held (10%)

$20,000

Total earned less retainage

$180,000

Less previous certificates for payment

$120,000

Amount certified and paid to the named contractor

$60,000

The owner pays $60,000 to the contractor named on the form. The $20,000 retainage stays held until the job is complete, per Autodesk. If the check or transfer shows a different payee or a different amount, the mismatch is the signal to stop and verify before treating the application as paid.

4. What the Contractor Records When Payment Arrives?

For construction accounting, the payment closes the loop on the progress billing cycle. A construction bookkeeper should record:

  • The amount received compared with the amount certified on the payment application

  • The payee name on the payment compared with the contractor named on the application

  • The payment date compared with the timeframe set in the contract

  • Retainage held to date, tracked separately from amounts paid

  • The certified G702 and the payment record, filed together

CCA's job costing guide shows how billed and received amounts connect to job costs.

Where Construction Cost Accounting Fits In?

Construction Cost Accounting provides construction bookkeeping services for contractors who bill owners on payment applications. Our construction bookkeeping services cover:

  • Amounts certified and amounts received reconciled for every payment application

  • Retainage tracked by job in construction accounting so held amounts stay visible

  • Payment records filed with the certified G702 and its certificate for payment, for every progress billing

  • A construction bookkeeper who follows up when a payment does not match the certificate

Learn more about our construction bookkeeping service.

After the architect certifies a payment application, the owner pays the amount certified to the contractor named on the form, within the contract's timeframe and minus retainage. Paying the named payee keeps the paper trail intact and helps avoid disputes and delays. Contractors who get paid without surprises are not leaving it to chance — their construction bookkeeping services match each payment to the certified amount and the named payee, in clean construction accounting.

Talk with a construction bookkeeper today

Get payments reconciled to certified applications with Construction Cost Accounting. 

constructioncostaccounting.com  |  (949) 889-3283 


Comments


bottom of page